Famco Chimney Cap & Crown Nationwide

Famco Chimney Cap & Crown in Woodland Park: What to Know First

We install, replace, and repair Famco chimney caps and crowns throughout Woodland Park, and most jobs are done in a single visit once we’ve seen the chimney. You’ll get a straight price before any tool comes off the truck, and if the work isn’t right, our 90-Day Done Right Promise brings us back at no charge. This page is for Woodland Park homeowners with a Famco cap or crown that’s rusting, leaking, or pulling away from the flue.

Call (973) 846-1622

If you’re seeing water in the firebox or rust streaks below the cap, call (973) 846-1622 and we’ll schedule a look. No trip charge inside Passaic County.

How Famco Products Fail - and How We Fix Them

Famco builds solid caps, but after enough New Jersey winters, every brand shows its weak spots. Here’s where we see Famco units in Woodland Park start to go, and what we do about it.

• Famco stainless steel caps rusting at the screen seam. The stainless body holds up fine, but the mesh screen is often a lighter gauge and the spot welds where it meets the frame are the first thing to go. In Woodland Park, where winter road salt rides the wind off Route 46 and Garret Mountain, we see this 5 to 8 years after installation. Fix is a new screen welded in place or a replacement cap depending on how far the corrosion has spread.
• Single-flue caps lifting off in nor’easter winds. Famco caps clamp to the flue with a pressure ring, but the bolts can loosen after repeated freeze-thaw cycles. We’ll find the cap hanging by one corner or completely gone. We re-seat it, replace any stripped hardware, and use galvanized lag bolts that won’t seize up next season.
• Multi-flue Famco caps collecting water at the crossbars. On the wider Famco units meant to span two or three flues, water pools where the crossbar braces meet the frame. The caulk Famco uses at the factory dries out and splits. We strip the old sealant, treat any surface rust, and re-bed the joints with a polyurethane sealant rated for chimney temperatures.
• Cast aluminum Famco caps turning white and pitting. The cast aluminum bodies look great for the first few years, but acid rain in this part of Passaic County eats at the finish. We can powder-coat these to match the original look, or replace with a stainless unit if you’d rather not think about it again for 20 years.
• Crown failure underneath a Famco cap. This is the one that gets missed. The cap is fine, but the concrete crown below it has cracked and water is running down the flue liner. No cap can fix that. We rebuild the crown with a proper overhang and expansion joint before remounting the Famco unit.

Our Famco Chimney Cap & Crown Process

Every Famco job we do in Woodland Park follows the same routine, whether it’s a cap replacement or a full crown rebuild.

1. 1
   Call (973) 846-1622. A live person answers. We get your address, what you’re seeing, and give you a straight price range over the phone before anyone drives out.
2. 2
   We climb up and look. Wendell or a member of his crew gets on the roof, inspects the cap, crown, flue top, and liner. We take photos you can see from the ground.
3. 3
   You see what we see. If the cap is fine and the crown is the problem, we tell you that. If it does not need doing, we say so first.
4. 4
   Parts decision. We tell you the Famco model you have, whether the OEM replacement is the right call, or if a quality aftermarket cap from our other trusted brands, like Olympia or Copperfield, will do the job for less without cutting corners.
5. 5
   The work. Old cap off, crown repaired or rebuilt if needed, new cap installed and secured, joints sealed with high-temp sealant.
6. 6
   The walkthrough and the promise. We show you the finished job at the roofline, go over what was done, and hand you the written 90-Day Done Right Promise. If anything isn’t right, one call brings us back.

What Famco Chimney Cap & Crown Costs in Woodland Park

Here are honest numbers for the Famco work we do most often in Woodland Park. These are prices we’ve stood behind on real jobs.

• Famco single-flue stainless cap replacement: $245-$395 installed
• Famco multi-flue cap (2-3 flues): $475-$850 depending on span and whether we’re fabricating a custom base
• Chimney crown repair (cracked mortar, no full rebuild): $325-$600
• Chimney crown rebuild with proper overhang and expansion joint: $1,100-$1,900 depending on access and crown size
• Crown coating (sealant application after repair): $175-$325

What moves the price: roof pitch, chimney height, whether the flue tile is spalled and needs grinding, and if the old crown has to be fully demolished or can be topped. We give you one number before any work starts, and it’s the same number on the invoice. Call (973) 846-1622 for an exact quote, estimates are free.

Why Woodland Park Homeowners Call Top Hat Chimney for Famco Work

Wendell Pike has been hauling brushes and buckets through Passaic County since 1999, and there’s a good chance he’s been on a roof on your street before. He worked chimneys near Rifle Camp Park when half these developments were still being framed. When you call Top Hat Chimney, you’re getting a locally owned, owner-operated shop that puts a name and license number on the work, not a franchise that rotated in last spring.

We work with Famco, DuraFlex, HeatShield, Gelco, Olympia Chimney, and Copperfield, so when a Famco part is backordered or overpriced for what it is, we can tell you honestly what will do the same job for less. The 90-Day Done Right Promise is in writing on every job. Live person answers the phone, around the clock. And yes, that person has been Wendell more than once at 10:30 at night.

Ask anyone on your street. They’ll tell you the same thing: the number you hear on the phone is the number on the invoice, and if it does not need doing, Wendell will tell you that first.

FAQs